Injector Dynamics fuel injectors are the result of batch testing large quantities of specially modified fuel injectors, and then carefully matching them into sets based on their dynamic flow across the pulsewidth range. The result is vastly superior cylinder to cylinder consistency, even at very low pulsewidths.

In addition to receiving tightly matched injectors, you will be provided with dead time compensation values across the entire pressure and voltage range of the injector. This data will insure that the compensations in your ECU work properly, and your air fuel ratios will remain consistent as atmospheric or voltage conditions change.

Injector Dynamics 725cc injectors (ID725) (Price: $115/ea)

• We have the necessary adaptors and pieces to make these injectors fit almost any application
• ALL ACCESSORIES ARE INCLUDED WITH EACH SET OF INJECTORS, INCLUDING THE INJECTOR CLIPS
• Honda applications - B series, H series, K series, F series, D series, NSX, Mitsubishi EVO and all 4G63, Toyota Supra, Subaru WRX, Nissan RB and SR with top feed, Nissan VQ, Hayabusa, Kawasaki ZX14, RX7 with top feed rails
• Almost any domestic application
• If you're unsure if these will work in your application, give us a call and we'll help you figure out what it will take
• These are a 48mm long body, shorter than normal injectors. The adaptor tops make them "normal" 60mm length and adapt them to 11mm (B series) or 14mm (K series) orings. The K series guys can run the injectors with no adaptors at all and they are the same length as the OEM rsx injectors so no spacers needed on the rail. These have a droplet size comparable to a 600cc Siemens injector and way better spray pattern and atomization than any other 1000cc injector on the market. The proper battery comp values are also provided with each set so you can set it up in your computer and have consistent a/f ratios as battery voltage fluctuates. Most other injectors don't offer that information at anything other than 1 voltage level. Price is per injector and includes the adaptor for the top and an injector clip with pins Please put your engine type in the comments section when purchasing

Injector Dynamics 850cc injectors (ID850) (Price: $110/ea)

Injector Dynamics is proud to release it's new ID850, offering a high quality solution where none existed before.

The ID850 was added to the Injector Dynamics lineup to fill the need for a high flow injector in a small package. Specifically, GM's LS motors, and various motorcycles applications such as Suzuki's GSX's, and Kawasaki's ZX machines.

With linearity matching that of the ID1000, and broad fitment options due to its small size, the ID850 is our most versatile injector.

Most notable is the fact that the ID850 is the only direct fit high flow injector available for GM LS3, LS7, L76, L92, and L99 motors that comes with complete characterization tables for GM PCM tuning.

That means easy and accurate tuning, for a better calibration with less time invested.

Injector Dynamics 1000cc injectors (ID1000) (Price: $115/ea)

• We have the necessary adaptors and pieces to make these injectors fit almost any application
• ALL ACCESSORIES ARE INCLUDED WITH EACH SET OF INJECTORS, INCLUDING THE INJECTOR CLIPS
• Honda applications - B series, H series, K series, F series, D series, NSX, Mitsubishi EVO and all 4G63, Toyota Supra, Subaru WRX, Nissan RB and SR with top feed, Nissan VQ, Hayabusa, Kawasaki ZX14, RX7 with top feed rails
• Almost any domestic application
• If you're unsure if these will work in your application, give us a call and we'll help you figure out what it will take
• These are a 48mm long body, shorter than normal injectors. The adaptor tops make them "normal" 60mm length and adapt them to 11mm or 14mm top orings. The K series guys can run the injectors with no adaptors at all and they are the same length as the OEM rsx injectors so no spacers needed on the rail.
• These have a droplet size comparable to a 600cc Siemens injector and way better spray pattern and atomization than any other 1000cc injector on the market. The proper battery comp values are also provided with each set so you can set it up in your computer and have consistent a/f ratios as battery voltage fluctuates. Most other injectors don't offer that information at anything other than 1 voltage level. Price is per injector and includes the adaptor for the top and an injector clip with pins Please put your engine type in the comments section when purchasing

Injector Dynamics 1600cc injectors (ID1600) (Price: $219.95/ea)

The ID1600 fills the gap between the ID1000 and the ID2000, and is a drop in replacement for older EV-1 style 1600cc injectors.
Unlike the older technology, the ID1600 has a very gradual rolloff into the lower non linear range, with none of the rollercoaster response caused by undamped pintle bounce.
This smooth response makes for easy idle tuning, even on small displacement motors. In addition to the excellent response, the minimum repeatable fuel mass matches that of the venerable ID1000, which means if you could make it idle with an ID1000, you can make it idle with an ID1600!
With a pressure capability of 9 bar this injector can flow as much as 2700cc/min while maintaining control and smooth response.

Basic Specifications

Nominal Dynamic Flow Rate - 1640cc/min @ 3.00 Bar (43.5 psi) Using Gasoline at 52 Degrees C (125 Degrees F)
Maximum Differential Fuel Pressure - 9.0 Bar (130.5 psi)
Fuel Compatibility - Compatible with Methanol/Ethanol/All Known Hydrocarbon Fuels. Incompatible with MTBE/Nitro Methane/Nitro Propane.
Electrical Connector - EV-1/Minitimer/LK-2

Injector Dynamics 2200cc injectors (ID2000) (Price: $239/ea)

• Finally, a great solution for people that need more than 1500cc/min!!
• The new Injector Dynamics ID2000 flows 2200cc/min at 3 bar (43.5psi) and is high impedance. That means no injector resistor or injector driver is needed. With the capability of running up to 130psi and flowing 3700cc/min, the needs for running multiple injectors per cylinder are gone on all but the most demanding methanol applications.
• Each injector includes the necessary adaptor top and electrical connector. The adaptor tops mechanically lock to the injector and also incorporate a 7 micron replaceable filter.
• Pricing is per injector, please order the qty needed for your application as well as list the application in the ‘comment’ box so we can assure you get the correct accessories for proper fitment.
• Visit www.InjectorDynamics.com for more information.